Chance favors the prepared!

Review

AR Wheeler Trigger Guard Install Tool Review

Wheeler Trigger Guard Tool

Editor’s note: Please welcome Evail Juan to Planandprepared.com. He will be a regular here, providing reviews on firearms, firearm accessories and tools, as well as other prepper related gear.

I recently received a Magpul Enhanced Trigger Guard as a gift (Thanks Sis). But upon reading how to change it out from the Mil Spec guard, I was shocked to learn the suggested method was to get an armorers block, roll pin punch, and a mallet to hammer the pins out. That being said, there is a disclaimer that should read “If you break the tab off, your lower will be JUNK!”

In this day and age why wouldn’t there be an easier way to change this out without the chance of destroying the lower receiver? Enter the Wheeler Trigger Guard Installation Tool. This tool is basically a specialized C-Clamp with 2 rods included. The long rod is for the removal, while the short rod is for the install. I actually read the directions carefully, which were precise and to the point.

Get ammo of your choice delivered right to your door!

The removal and install took about 30 minutes to complete. The only reason that took a little longer than expected was because I aligning the pin and install tool to start the pin into the hole. Seems like a third hand would be nice here for this process. But with a little tongue waggling, a few choice words, and a bit of patience I was able to get it to fit.

Once I was able to get it aligned into the hole, then it was just a simple matter of making sure the pin was flush with the receiver. Then voila, the change was complete!

All in all I would give the Wheeler Trigger Guard Install Tool a 4.75 stars. And the only reason I’m not giving 5 stars is due to the fact that holding all the components and trying to get it aligned was not an easy task.
Continue reading

EDC Gun Review – Glock Compact

I had someone email me the other day, asking why I didn’t do a review of the Glock I carry as an EDC firearm. While I don’t carry a Glock off duty, I am sure there are plenty of folks out there who might carry it as their EDC gun.

So, here you go! My review of a Glock as an EDC.

I will actually be looking at two compact (mid-sized) Glocks. I will look at the Glock 23 (.40 S&W) and the Glock 32 (.357 Sig.) The Glock 23 is a Gen 4, while the Glock 32 is a Gen 3.

The first Glocks were produced in 1982, and started arriving in the US by 1988. There was a lot of doubt in the “gun world” about whether a plastic (polymer) firearm was worth anything. The huge success of Glock has answered it’s critics. It is now one of the most popular handguns in America today. According to Glock’s website, 65% of police departments in the US issue/carry Glock pistols.

This success was partly due to the clever and effective marketing of Glock, who sold their pistols to the police at a discount. When police departments saw how effective and well-built the Glocks were, plus the fact that Glock 17s could hold 17 rounds of 9mm, they began carrying them en-mass. This gave credence to Glock with the general public, and the rest as they say is history.

The Glock 23/32 is a polymer framed pistol and almost 7 inches in length. (5 inches high.) Its 4 inch barrel is made of ordnance grade steel, and has a nitrate finish. The pistol (Glock 23) weighs about 23.5 oz or so (unloaded). The 32 weighs 21.5 oz unloaded.
Continue reading

Off-grid cooking method – Here is one we recommend

off grid cooking

Adding rabbit meat to the oil and seasoning

Editor’s note: I want to welcome Cheryl L (my mom) to the site with her first article! Enjoy!

No matter what you are prepping for, at some point in time food preparation must enter into your preps. I am always trying to find ways to cook using a minimum amount of time, energy, effort, and fuel. So I plan my preps accordingly.

I prefer to keep my life simple and that includes getting everything done in the morning and taking it easy after all the work is done.  This is one of the reasons that I decided to purchase a thermal cooker.

Another reason I thought a thermal cooker would be a wonderful idea is for the ease of cooking a meal whether on a regular stove, a rocket stove, an open campfire, or in any emergency situation.  We live in tornado territory and I can take a thermal cooker down into the shelter along with the already stored dehydrated meals and water, etc. so that I can prepare them for my family if the need arises.  Be it a rabbit dinner or emergency food storage, I feel secure in having the means to take care of them.

I looked and researched on the internet, reading about several different thermal cookers. After some study I finally settled on the Saratoga Jack 7L thermal cooker.

I went with the Saratoga because it received a lot of positive feedback on Amazon, and because it comes with two heavy-duty pans that nestle together for cooking, (cook two separate pots at once) a lid, a cook book and of course the vacuüm cooker.

Saratoga Jack 7L thermal cooker

The Saratoga Jack thermal cooker is simple to use. You follow your regular recipes, bring the temperature to a rolling boil for a few minutes, and then seal the pot in the cooker.  And depending on the recipe your food is ready and waiting for you in the evening when you are ready to sit down to dinner.
Continue reading

EDC Gun Review – Smith/Wesson M&P Shield

shieldA few months ago, my brother and I were visiting a local gun show. I do not usually buy firearms at gun shows, as they tend to be a bit overpriced in my opinion. But I have found some good deals on parts and accessories, and I love to “window shop”.

Anyway, while making our way from table to table, my brother came upon a slightly used Smith and Wesson M&P Shield in .40 cal. The owner allowed him to field strip it, and we realized it was in excellent condition, LNIB. (Like New In Box.) After some slight haggling, my brother bought it. And after a trip to the range, I thought I would give it a review as an EDC firearm.

The M&P Shield is a black polymer framed, striker fired pistol. It is slim and light weight. The pistol is a bit over 4.5 inches tall, and weights about 19 oz. The barrel is 3.1 inches long. So for a 40 cal pistol, the Shield is small enough to conceal, but offers significant stopping power.

As I mentioned, this particular pistol is a .40 cal. Smith and Wesson also makes the M&P Shield in 9mm, but because our ammo stores are .40 cal, we went with the .40 cal. The .40 comes with a single stack 6 or 7 round magazine.
Continue reading

Prepper Budget Carbine Review – Hi Point 40 cal carbine

carbine1I am always on the lookout for quality firearms. I fully believe that when it comes to firearms, you generally get what you pay for. So I do not mind spending a bit more if I know that I am getting a well built, reliable firearm. And if there is a chance of getting a quality firearm on a budget, then I am certainly all in.

I have been looking for a pistol carbine for quite some time. I decided I wanted a 40 cal carbine since my pistols were 40 cal, and I have plenty of 40 cal ammo. Who doesn’t like the idea of having multiple weapons and weapons platforms that you can share ammo between?

I initially wanted to get a Beretta CX Storm. But the internal parts of that carbine are made of polymer, not metal. I have no issue with polymer framed firearms, like my Glock. But I’m a bit unsure of a firearm with polymer internal parts.

To replace those polymer parts with metal would double the price of the gun. That made it inefficient for me from a cost stand point.

I also was interested in a Kel-Tec Sub 2000 that took Glock 23 magazines. But I have yet to be able to find one. (At least one that wasn’t used AND double the MSRP.) I really want a new Gen 2 Sub 2000, but I doubt I will ever find one. 🙁

I checked other 40 cal carbines, but typically found something about them that did not appeal to me. Then one day I came across a brand new, still in the box Hi Point 40 S&W carbine. Now obviously, this gun is ugly. No, I mean UGLY! (What Hi Point isn’t?) But I had heard good things about Hi point’s overall reliability. And for the price I paid for it, (got a SMOKIN’ deal well under $300) I decided “What the hell!”

I took it home and noticed that there was going to be “some assembly required”. But not to worry. The assembly was fairly simple. I had to mount the knob for the slide release, and mount the grip handle. (I got the version with the vertical grip.) Really, this took me less than 5 minutes to complete. The carbine comes with the tool you need to put it together and to field strip it.
Continue reading

EDC Holster Review – Tactical Rig Osborn Holster

holster1I am a firm believer in having a self-defense type weapon as a part of your EDC. (Every Day Carry). And I also advocate carrying that weapon concealed. While I carry a Glock 23 with a Streamlight Tactlite on duty, off duty I prefer something that is much easier to conceal. I carry a Sig Sauer P238.

The P238 comes with its own carry/conceal holster, a nice touch by Sig. But it rode too high on my waist for my liking. And it did not feel like it was completely secure.

So when the good folks at Osborn Holster offered to make me a carry/conceal leather holster for my Sig, and make it large enough to also carry a spare magazine, I said “Hell Yeah!”

For those of you who are not familiar with Osborn Holsters, they have been in the market for the past 3 to 4 years. They specialize in making custom holsters for almost any style of pistol. Osborn holsters are made right here in the USA, headquartered in Texas.

I ordered the IWB (Inside Waist Band) Tact rig for my Sig, and was surprised when it arrived less than a week later. I order firearm parts all the time. Many times it takes a week just to process the order and then ship the parts. So to have my holster fabricated and sent to me in that amount of time left me pleasantly surprised.

The first thing I noticed when I took it out of the package was how durable, yet flexible the leather was. I also noticed that the holes for the magazine attachments and the kydex had been reinforced with eyelets, which should help with the holster’s durability. I’m a big fan of buying products that are durable and long lasting. So I give bonus points for things like that.

The P238 fit securely in the Kydex molding. It was a bit snug, and took some effort to pull out. But the holster uses screws with rubber spacers to attach it to the leather. This means that the amount of retention can be adjusted. So between adjusting the screws, and normal use (break in period), the tight retention should not be an issue.
Continue reading

Plan and Prepared
Preparedness knowledge and tips from a veteran police officer!
Sign up for Newletter
Enter your email address to subscribe to this site and receive notifications of new posts by email. NO SPAM ever!
Trending Posts
Click here to vote!
Shop
Filters up to 100,000 gallons of water!
For about $20, filters up to 100,000 gallons of water! Click here to get it now
Get your emergency, hand crank radio here!