Editor’s note: Please welcome Evail Juan to Planandprepared.com. He will be a regular here, providing reviews on firearms, firearm accessories and tools, as well as other prepper related gear.
I recently received a Magpul Enhanced Trigger Guard as a gift (Thanks Sis). But upon reading how to change it out from the Mil Spec guard, I was shocked to learn the suggested method was to get an armorers block, roll pin punch, and a mallet to hammer the pins out. That being said, there is a disclaimer that should read “If you break the tab off, your lower will be JUNK!”
In this day and age why wouldn’t there be an easier way to change this out without the chance of destroying the lower receiver? Enter the Wheeler Trigger Guard Installation Tool. This tool is basically a specialized C-Clamp with 2 rods included. The long rod is for the removal, while the short rod is for the install. I actually read the directions carefully, which were precise and to the point.
The removal and install took about 30 minutes to complete. The only reason that took a little longer than expected was because I aligning the pin and install tool to start the pin into the hole. Seems like a third hand would be nice here for this process. But with a little tongue waggling, a few choice words, and a bit of patience I was able to get it to fit.
Once I was able to get it aligned into the hole, then it was just a simple matter of making sure the pin was flush with the receiver. Then voila, the change was complete!
All in all I would give the Wheeler Trigger Guard Install Tool a 4.75 stars. And the only reason I’m not giving 5 stars is due to the fact that holding all the components and trying to get it aligned was not an easy task.
A while back, I wrote an article for folks that are brand new to prepping. If you missed it, click here to read it. Anyway, I got some positive feedback on that article, but I also received a few emails asking me to be a bit more specific. They wanted to know where and what they should start with first.
In particular, one email from a lady told me she was on a fixed, very tight income. She had very limited resources, and was asking me what should be the priorities for her, even more so than in the above listed article. I could tell from her email she was feeling a bit overwhelmed. She wanted to be more prepared, but could not spend very much each month.
That’s understandable. Beginning preparedness can feel like a daunting task. You can also look at everything you might potentially need, and feel concerned because your funds are limited. But it doesn’t have to be that way.
I have decided to break down that beginning prepping article a bit more, and go into detail as to what I believe should be your top priorities if you are on a budget. Keep in mind that these are the top priorities in almost every disaster scenario, NOT just a huge SHTF event. As always, I stress that you need to start with the most probable scenarios, and work your way outward.
For this article, I’m assuming that you already have developed emergency plans. That to me is your obvious #1 priority. Failing to plan is planning to fail, and hope is not a plan. Instead, this article will focus on what resources you should be collecting first. (For more info on preparedness planning, click here.)
These categories are listed in order of importance (in my opinion). For each category I list the basics for that category that you should work on first. Once you have the basics in that category covered, move on to the next. Or if you can, try to cover more than one category at a time! For example, I list water storage over food storage. (3 days without water/3 weeks without food.) But if you can cover both categories at the same time, you are that much further ahead.
At the end of each category I will list “additional” items. These are items that while I feel are important, they are areas/items that you can come back to once you have all of your basics covered.
With the elections just weeks away, I wanted to give some resources for those of you who might be preparing for the results of this year’s election. I also wanted to give you something to think about if you have not yet thought about preparing for it.
When I first put this site together, I told myself that I would not delve into politics. To me, preparedness transcends political and ideological belief. But I cannot hold my tongue any longer when I see our country’s freedoms being stripped away. I feel like if I don’t say/do something and instead remain silent, I am complicit with it happening.
So I have begun to speak out.
I’m not going to sit here and tell you who you should vote for. I truly believe that most people already know who they plan on voting for. If you are an informed voter, then you should already know where the candidates stand on issues like the 2nd Amendment.
I had a discussion with a more left leaning co-worker the other day. He told me that every time a Democratic president gets elected, gun sales spike. Then it calms down and then nothing really happens. Hence gun owners have nothing to panic over.
This has been true in the past. This time however, I think things are different.
I chuckled a bit, and mentioned that in July, Massachusetts Attorney General Maura Healey banned “Assault Weapons” in her state. No congressional debate. No vote of the people. She simply banned them. So don’t think for a second that it could not happen in your state, or worse on a national level.
He asked me the question so typical of anti-gun folks, “Why do you need an AR? All it is good for is killing people.”
I had someone email me the other day, asking why I didn’t do a review of the Glock I carry as an EDC firearm. While I don’t carry a Glock off duty, I am sure there are plenty of folks out there who might carry it as their EDC gun.
So, here you go! My review of a Glock as an EDC.
I will actually be looking at two compact (mid-sized) Glocks. I will look at the Glock 23 (.40 S&W) and the Glock 32 (.357 Sig.) The Glock 23 is a Gen 4, while the Glock 32 is a Gen 3.
The first Glocks were produced in 1982, and started arriving in the US by 1988. There was a lot of doubt in the “gun world” about whether a plastic (polymer) firearm was worth anything. The huge success of Glock has answered it’s critics. It is now one of the most popular handguns in America today. According to Glock’s website, 65% of police departments in the US issue/carry Glock pistols.
This success was partly due to the clever and effective marketing of Glock, who sold their pistols to the police at a discount. When police departments saw how effective and well-built the Glocks were, plus the fact that Glock 17s could hold 17 rounds of 9mm, they began carrying them en-mass. This gave credence to Glock with the general public, and the rest as they say is history.
The Glock 23/32 is a polymer framed pistol and almost 7 inches in length. (5 inches high.) Its 4 inch barrel is made of ordnance grade steel, and has a nitrate finish. The pistol (Glock 23) weighs about 23.5 oz or so (unloaded). The 32 weighs 21.5 oz unloaded.
Several months ago, I wrote an article on building your own AR on a budget. (Click the link if you missed it.) It has become this site’s most popular article as more and more people take an interest in owning and building an AR rifle.
In that article, I wanted to give readers the information they would need to build their own AR 15. I tried to stick to the basics and not overwhelm the reader. I also listed AR parts that would not “break the bank”. The response was very positive.
I received a lot of email about it, asking all sorts of different questions. The one question that kept popping up was: “I want to build a quality AR and I am willing to spend more $$. Which parts would you recommend?”
Now before I answer this, I want to give a little clarification. While I have always advocated getting quality firearms (because some day your life might depend upon them), that does not mean that I believe that you always have to spend huge amounts of money to get quality. Yes, I believe that you get what you pay for. But sometimes, you can find quality on a budget.
If you are like me, you love watching exciting “Action” movies. Who doesn’t love a good movie scene with an exciting car chase and lots of explosions? Unfortunately, many times what we see in the movies is NOT what happens in real life. Firearms are no exception. In fact, many times Hollywood (and the public in general) gets firearms and how they really function completely WRONG.
So I thought I would take a look at 5 myths or beliefs on firearms that are either erroneous, or at the least very misleading.
#1 – Silencers are whisper quiet
If you are a James Bond fan, you have seen our hero sneak into some fortified castle, and use his Walter PPK with a silencer to quietly take out the bad guys. Sadly, this Hollywood depiction of a silencer is not accurate.
Silencers reduce a portion of the noise, this being the pressure wave from the expanding propellant gases. It does NOT reduce the noise of the sonic crack a supersonic round creates when fired.
To put this into layman’s terms, a typical supersonic round fired from a commercially available firearm is between 140-190 decibels. Variables such as caliber, barrel length, etc can change this some. But typically, this is the most common range for the sound made from firing a gun.